How to install new XPROG BOX 5.60 on Windows 7 32bit
XPROG-M nowadays has been updated to XPROG-BOX V5.60 ECU programmer. Today, XPROG BOX 5.6.0 is verified to work well to read and write EEPROM 93C66. Here’s the instruction on how to install XPROG-BOX...
View Articlewhat’s the difference between xprog-m v5.55 and xprog-m 5.60
Xprog-m ECU programmer updated to V5.60 version added more ecu chip Authorizations,Here obd2express.co.uk will list the ecu chip Authorizations about xprog-m 5.60, and give the Comparison between...
View ArticleK-Touch New Genius ECU Chip Tuning Tool Test List
New Genius K-Touch MAP OBD2 Master with Free Winols 2.24&ECM Titanium 1.61 is update version of Kess v2, more new vehicles supported. Here obd2express shares customer’s feedback and test list on...
View ArticleHow to read Mercedes W203 1J35D MCU with xprog-m 5.0 [pictures]
I have managed to read 1J35D MCU of Mercedes-Benz W203 EZS with Xprog-m 5.0 ECU programmer.Here are some useful tips/ infomation for sharing. Wish i help you out also. The China Xprog-m i used XPROG...
View ArticleFGtech Galletto 4 vs CMD flasher vs Alientech Ktag Kess v2 vs MagPro
Invested on Chinese ECU programmers, FGtech Galletto 4, CMD flasher v1251, clone Alientech (Ktag and Kess v2), MagPro x17… I read a lot, with each opinion. Over all that I read is old (<2011). So...
View ArticleHow to use KTAG KTM100 to read BMW F10 EDC17C41 [tips]
Here are some tips of “reading error” for you when reading EDC17C41 DDE8 520d F10 ecu with Ktag clone, offered by experienced users. TRY OWN YOUR OWN RISKS!! Tip 1 – replace oscilator near the nxp...
View ArticleV54 FGTech Galletto 4 wiring diagram for BMW Bosch EDC17 MEVD17
Here is the FGTech BOOT Tricore user manual for BMW ECU Bosch EDC17 and MEVD17, wiring diagrams attached also. BMW ECU here includes: Bosch EDC17 CP02 . . . . . . . . . . . . . . . . . . . . . . Micro...
View ArticleChecksum Family Manual for ECM Titanium v1.61
What is Checksum? Checksum is the security algorithm with which are encoded files stored inside the engine control units; if the modified files you are tuning, it wasn’t signed with the correct...
View ArticleHow to solve Carprog v8.21 Unit CRC error (delete LIB file)
Here is a customer solution of Carprog v8.21 with the following error message: Unit CRC error: Delete LIB file and make UPDATE -> INTERNET A1 OBDII adapter (resistor must be rem) User solution: TRY...
View Article(solved) Xprog-m Xprog-box v5.55 Safengine error”□□□□”
When i installed Xprog-m v5.5.5 software, the Safengine error □□□□ popped up Solved by professional technicians! Open Computer Management and the find out ET199 to uninstall it (there should be lots...
View ArticleHow to reflash CARPROG MCU AT91SAM7S256
Here is a experience from DK forum members who made this possible about how to reflash CARPROG Mcu AT91SAM7S256 Tool use: Carprog clone v8.21 firmware We need the stuff: 1- AT91SAM7S256.bin 2- Jtag...
View ArticleHow to reset BMW airbag with Carprog v8.21 v9.31
It just takes 1 minute to reset and repair airbag computer in your office, with the new CarProg v8.21 or CarProg v9.31 airbag reset tool. Why you need to reset or replace airbag tool? BWM airbag...
View ArticleWhich ECU programmer better, Xprog-m or UPA-USB?
People talks a lot on XPROG-M and UPA at forum,Which better? any difference of them? This post make a detail comparison table of X-prog m 5.5 and 2014 Upa v1.3 ecu chip tuning tools. Hope it can help...
View ArticleRework Ktag Kess V2 pcb hardware-no issue
Share free solutions of reworking clone Ktag and Kess V2 ECU tuning tools to work completely like the genuine. Original PCB in the photo … use if you have any other issues. Replace by quality...
View ArticleHow to do when you lift pin 55 on Carprog
Now I have succeeded in one Carprog unit(CARPROG FULL V9.31), with help of a sewing needle. It will go wrong because I get up two pin, and then I can not solder back the faulty pin. Now I have managed...
View ArticleYanhua MB CAN Filter 18 in 1 User Manual
It’s a user manual of Yanhua Mercedes-Benz CAN filter 18 in 1, including installation/connection instruction and vehicles available. How to use YH MB CAN Filter: This Mercedes Benz can filter should...
View Article(solved) Xprog-m v5.5.5 “verify error” fixed by Xprog v5.51
Here are important tips for all xprog users when they got this problem “verify error” during reading motorola mcu, and after try several time is read maybe. Xprog software used: Usually two xprog with...
View ArticleMPPS V18 eu clone hardware & mpps software review
This is MPPS V18 clone review from diy users at http://www.obd2express.co.uk/. Part 1- review on MPPS V18 cable: The cable is a nice quality OBD male cable, it looks like many ones, but it’s a...
View ArticleMPPS v21 v18 v16 v13 software download
This clone MPPS tools are a 1:1 of the original. Here download the crack mpps software v21 v18 v16 v13 with buying cables together. MPPS software download: MPPS V18 download MPPS V16 clone MPPS V13...
View ArticleFgtech galletto 4 v54 OK to read & write bmw edc17?
Is it ok to buy Fgtech galletto 4 v54 to read and write BMW ECUs? To work with edc17 without issues? Here goes to questions and answers. Questions: Galletto brick 730d ecu and fail with too many BMW...
View Article